The Stelrad LST Plus Radiator 650mm High x 650mm Wide was created by the UK's leading radiator manufacturer to simplify product selection in areas where safety is critical.
The attractive flat panel outer casing can be reversed to allow piping flexibility, whilst the emitter provides excellent outputs through convection.
Guaranteeing performance and dependability, all Stelrad LST Plus Radiators come with a host of features, explained below.
Stelrad LST Plus Radiator Features:
- Fully compliant with all safety standards
- Meets the strict requirements of the NHS Guidance Note for 'Safe hot water and surface temperature'
- Can be installed in domestic, commercial and public buildings running heating systems with total public safety assured.
- Can significantly reduce costs
- Easy to install
- Anti-bacterial paint as standard
- Robust packaging protects the emitter and casing during storage and transit to ensure the product arrives in pristine condition
- All specified components are complete within the packaging
- Attractive flat panel
- Security fittings to prevent unauthorised access to the emitter
- Unique seam fixing bracket system
- Provides high outputs through convection
- Outstanding heating performance
- Guaranteed to perform to a maximum working pressure of 116 psi (8 bar) and conform to BS EN 442
- Safety grilles Supplied as standard
- Can be assembled to run full width
- Can be assembled to cover pipes on one side only (650 and 750 high models)
- Supplied with integral remote sensing thermostat valve to allow adjustment of room air temperature
- Supplied with arthritic adaptor as standard
- Supplied with lockshield valve as standard to discourage unauthorised tampering
Stelrad LST Plus Radiator Technical Specs:
|
Overall Height (mm)
|
650
|
|
Emitter Height (mm)
|
400
|
|
Overall Length (mm)
|
650
|
|
K1 Output (watts)
|
264
|
|
K1 Output (BTUs)
|
902
|
|
P+ Output (watts)
|
388
|
|
P+ Output (BTUs)
|
1332
|
|
K2 Output (watts)
|
456
|
|
K2 Output (BTUs)
|
1557
|
Stelrad LST Plus Radiator Dimensions:
Stelrad LST Plus Radiator In Depth:
INSTALLATION
Everything required for the installation of the Stelrad
LST Plus can be found in the one robust pack. This
includes the emitter and radiator casing panel,
together with the required brackets. These are of a
strong design, with open top and deep slots, which
facilitate easy and secure installation. Plastic inserts
seat the radiator precisely on the bracket minimising
expansion and contraction noise. The neat nickelplated
plug and vent provide a watertight joint.
The radiator valves and pipework, together with kick
grille/pipe cover grille and all required hardware fixings
can also be found in this pack.
REMOTE SENSING THERMOSTATIC VALVE
The Danfoss RA2000 is designed specifically for
commercial heating systems and can be pre-set to
allow adjustment of room temperature between 5°C
and 26°C. Special tools are not required, as the
valve is gland seal removable.
Suitable for both 1/2" steel and 15mm copper piping,
with left or right hand, same end connections for flow
and return, giving flexibility of installation.
LOCKSHIELD VALVE
Able to withstand 10 bar static pressure, the valve has
a drain tap adaptor available, which can also be used
as a filling point. Mandatory fittings should be used in
order to comply with current water regulations.
CONNECTIONS
Each Stelrad LST Plus radiator has 2 x 1/2"
connections as standard, complete with Danfoss
remote sensing thermostatic radiator valve, pre-piped
with 2 x 1/2" BSP connections at 50mm centres
positioned at either left or right of the casing.
ANTI-BACTERIAL PAINT
Every Stelrad LST emitter is subjected
to a multi-stage cleaning process before
the paint is applied. This involves
several rinsing stages, including an iron phosphate and
demineralisation phase.
The first coat of paint is applied by electrophoresis and
the radiator is then stoved and cooled. Followed by a
second powder coat in warm white and the emitter
goes through a final curing stage. It is then allowed to
cool prior to packaging.
All exposed painted surfaces are finished in a long
lasting anti-bacterial coating.
The following link contains further information about this product
